Rolling friction coefficient testing quantifies the resistance a rolling body experiences against a counter-surface, a decisive parameter for tires, bearings, wheels, casters, and polymeric components. This article explains the underlying physics, specimen requirements, measured parameters, and the principal test methods—including inclined plane, roll-down, drum, towed wheel, pendulum decay, and tribometer techniques—together with applicable ISO and ASTM standards and typical industrial applications.
Technical Overview
The rolling friction coefficient, more precisely termed the rolling resistance coefficient (Crr or μr), is defined as the ratio of the tangential resisting force Frr to the normal load N acting on a body in rolling contact: Crr = Frr / N. It is a dimensionless quantity that may also be expressed in N/kN, particularly in tire testing. Unlike the sliding coefficient of friction, rolling resistance is not governed by interfacial shear alone; it originates from viscoelastic hysteresis within the contacting materials, micro-slip inside the contact patch, plastic deformation of surface asperities, adhesion effects, and lubricant drag in lubricated contacts.
Because of these mechanisms, the rolling friction coefficient is one to three orders of magnitude lower than typical sliding values: hardened steel balls on steel plates commonly exhibit Crr of 0.0005 to 0.002, rolling bearings 0.001 to 0.005, rail wheel–rail pairs 0.001 to 0.003, and passenger car tires on a smooth steel drum approximately 0.007 to 0.015. The value is strongly dependent on normal load, rolling speed, temperature, material hardness, surface roughness, and the diameter of the rolling element, so any reported result must state the full test condition set. International frameworks such as ISO 28580 and ISO 18164 for tires and ASTM G115 for general friction measurement provide the basis for comparable, traceable reporting, and testing is typically performed in accredited third-party laboratories or manufacturer laboratories with calibrated force and torque instrumentation.
Testing Samples
Elastomer and Rubber Specimens
Cured rubber sheets, tread compounds, and standard rollers are tested to characterize hysteresis-dominated rolling losses. Specimens are usually conditioned at 23 ± 2 °C and 50 ± 5 % relative humidity for at least 24 hours, and test surfaces are cleaned with a suitable solvent such as isopropanol to remove mold release agents and contaminants.
Polymer Wheels, Rollers, and Casters
Finished or prototype wheels, conveyor rollers, guide rollers, and furniture or industrial casters made of polyamide, polyurethane, PTFE, or elastomer compounds are tested as complete rolling assemblies to capture realistic geometry, tread hardness, and bearing influences.
Rolling Bearings and Precision Balls
Deep-groove ball bearings, cylindrical roller bearings, thrust bearings, and individual balls made of bearing steel, ceramics such as silicon nitride, or glass are evaluated for rolling friction torque and running efficiency, which directly affect machinery energy consumption.
Tires
Passenger car, light truck, and commercial vehicle tires are tested as complete inflated assemblies mounted on a standard rim, in accordance with the drum-based procedures of ISO 28580, which specifies drum diameter, load, speed, inflation pressure, and thermal stabilization requirements.
Wheel–Rail and Flooring Material Couples
Wheelset steel specimens against rail segments, and standardized wheels against flooring materials such as vinyl, rubber, or concrete, are tested to support rail vehicle energy modeling and flooring ergonomics or mobility product assessments.
Testing Items
Typical reported quantities include:
- Rolling friction coefficient / rolling resistance coefficient (dimensionless or N/kN)
- Rolling resistance force (N) at defined load and speed
- Rolling resistance moment or torque (N·m or N·mm)
- Start-to-roll (breakaway) threshold angle or force
- Speed dependence curve of Crr, for example 10–140 km/h for tires
- Load dependence of Crr at stepped normal loads
- Temperature dependence, typically −10 °C to +40 °C using environmental chambers
- Running-in behavior and stabilized steady-state values
- Starting and running torque for rolling bearings
Testing Methods
Inclined Plane (Ramp) Method
A ball, cylinder, or wheel is placed on a plane faced with the mating material, and the inclination angle is increased slowly until continuous rolling initiates. The rolling friction coefficient is approximated as the tangent of the threshold angle. The method is simple, quasi-static, and well suited to hard, rigid material couples for comparative screening, though its sensitivity is limited by angle resolution and specimen roundness.
Roll-Down Distance and Deceleration Method
The specimen or an instrumented carriage is released from a fixed height on a ramp and allowed to coast on a level track. From the energy balance, Crr equals the release height divided by the stopping distance; alternatively, an accelerometer yields Crr as deceleration divided by gravitational acceleration, corrected for air drag and carriage bearing losses. This method is widely used for casters, wheels, and spherical products such as golf balls.
Rotating Drum Method
The drum method is the reference technique for tires under ISO 28580 and ISO 18164. The inflated tire is pressed against a smooth steel drum of 2.0 m diameter at a specified load and 80 km/h speed, and the rolling resistance is obtained by measuring the drum spindle reaction force, the drum torque, the tire axle force, or the deceleration during coast-down. A skim test or unloaded coast-down is run to subtract machine parasitic losses, and results are corrected to reference temperature conditions. Laboratory-scale drums of 200 to 850 mm diameter with load-cell instrumented arms are used for material-level studies of rubber and polymer rollers.
Towed Wheel Method
The wheel or roller assembly is towed at constant speed across a flat track or moving belt carrying the counter-surface, and the horizontal towing force is measured with a calibrated load cell. This approach permits evaluation on realistic surface textures such as asphalt, concrete, carpet, and flooring, provided that carriage bearing friction is determined and subtracted and that speed and temperature are controlled.
Pendulum Decay Method
A ball or roller mounted on a pendulum arm rolls back and forth across a flat specimen, and the successive amplitude decay is recorded optically or with an encoder. The energy loss per cycle, derived from the amplitude reduction, is converted into a rolling resistance moment. The method is highly sensitive for small, hard specimens at low loads and requires minimal instrumentation.
Instrumented Tribometer with Rolling Contact Module
Ball-on-disc and roller-on-disc tribometers operate in pure or near-pure rolling, with the friction torque measured by a precision sensor on the specimen holder and the slide-to-roll ratio monitored to confirm negligible slip. These systems map the rolling friction coefficient as a function of load, speed, temperature, and lubricant, and are standard tools for lubricant and advanced material research. Guidance on test design, measurement uncertainty, and reporting is provided by ASTM G115.
Applications
Rolling friction coefficient testing supports product development, regulatory compliance, and energy-efficiency engineering across many sectors:
- Automotive tires: rolling resistance classification for fuel economy labeling and range prediction, based on ISO 28580 single-point results and ISO 18164 multi-point curves
- Electric vehicle and drivetrain engineering: bearing friction characterization for efficiency modeling and thermal management
- Industrial machinery: selection and qualification of rolling bearings for reduced energy consumption
- Conveying and intralogistics: energy-efficient roller and wheel specification for conveyor lines and automated guided vehicles
- Railway engineering: wheel–rail rolling resistance inputs for traction energy and network energy modeling
- Material handling and packaging: caster and roller performance for carts, trolleys, and packaging machinery
- Consumer and sports products: bicycle tires, golf balls, skateboards, and mobility wheels
- Polymer and rubber R&D: correlation of viscoelastic properties, silica and resin formulations, and tread compound development with rolling loss
FAQ
How does the rolling friction coefficient differ from the sliding coefficient of friction? The rolling coefficient arises mainly from hysteresis and micro-slip rather than macroscopic interfacial shearing, so it is typically 0.001 to 0.02, versus 0.1 to 0.8 for many sliding pairs, and it is far more sensitive to load, speed, geometry, and temperature.
What is a typical value for a modern passenger car tire? Under ISO 28580 conditions, mainstream tires measure roughly 7 to 10 N/kN, while optimized low-rolling-resistance designs reach approximately 6 to 7 N/kN, with each unit corresponding to measurable fuel or energy savings over the service life.
How are machine and parasitic losses eliminated in drum testing? A skim test or unloaded coast-down is performed on the same rig, and the measured machine loss is subtracted from the loaded measurement, after which the result is corrected to the reference speed and temperature specified by ISO 28580.
Can testing be performed at extreme temperatures or with lubricants? Yes. Environmental chambers allow evaluation from sub-zero to elevated temperatures, and tribometer rolling modules operate with controlled lubricant supply, film thickness monitoring, and slide-to-roll ratio adjustment.
How should results be reported? Every value must be accompanied by the normal load, rolling speed, temperature, counter-surface and its condition, specimen geometry, conditioning history, and the measurement method and standard applied, because the rolling friction coefficient is a system property rather than a pure material constant.
Which organizations publish relevant standards? ISO (for example ISO 28580 and ISO 18164 for tires, ISO 8295 for comparison with sliding film friction), ASTM International (ASTM G115 general friction guidance), JIS, EN, and GB national standard systems all cover aspects of rolling and general friction measurement, and accredited third-party laboratories provide conformity testing against these frameworks.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing