Ubicación: Global + English
Global Global Algérie Français Algeria English Angola Português Angola English Argentina Español Argentina English Australia English Austria Deutsch Austria English Azerbaijan English Azerbaijan Русский Bahrain English Bangladesh English Belgium English Belgium Français Belgium Nederlands Brazil Português Brazil English Bulgaria български Bulgaria English Cameroon English Cameroon Français Canada English Canada Français Chile Español Chile English China 中文 China 日本語 China English Colombia Español Colombia English Croatia English Czech Republic Čeština Czech Republic English Denmark English Djibouti English Ecuador Español Ecuador English Egypt English Estonia English Ethiopia English Finland Suomi Finland English France Français France English Georgia English Georgia Русский Germany Deutsch Germany English Ghana English Greece Ελληνικά Greece English Guatemala Español Guatemala English Hong Kong, China English Hong Kong, China 中文 Hungary Magyar Hungary English India English Indonesia English Iraq English Ireland English Italy Italiano Italy English Ivory Coast Français Ivory Coast English Japan 日本語 Japan English Jordan English Kazakhstan Русский Kazakhstan English Kenya English Kuwait English Kyrgyzstan Русский Kyrgyzstan English Latvia English Lithuania English Malaysia English Mauritius English Mauritius français (Maurice) Mexico Español Mexico English Moldova Română Moldova English Mongolia English Morocco English Morocco Français Mozambique Português Mozambique English Netherlands Nederlands Netherlands English New Zealand English Nigeria English Norway English Oman English Pakistan English Paraguay Español Paraguay English Peru Español Peru English Philippines English Poland Polski Poland English Portugal Português Portugal English Qatar English Republic of Korea 한국어 Republic of Korea English Romania Română Romania English Saudi Arabia English Serbia Српски Serbia English Singapore English Slovakia English Slovenia English South Africa English Spain English Spain Español Sri Lanka English Sweden English Switzerland Deutsch Switzerland Français Switzerland Italiano Switzerland English Tanzania English Thailand ไทย Thailand English Togo English Togo Français Tunisia English Tunisia Français Türkiye Türkçe Türkiye English Turkmenistan Русский Turkmenistan English Ukraine Українська Ukraine English United Arab Emirates English United Kingdom English Uruguay Español Uruguay English USA English Uzbekistan English Uzbekistan Русский Vietnam Tiếng Việt Vietnam English

Evaluation of Fineness of Grind Test Results for Coatings: Methods, Standards and Acceptance Criteri

Fineness of grind testing is a fundamental quality-control measurement used to evaluate the degree of pigment and filler dispersion in paints, varnishes, and printing inks. This article explains how fineness of grind results are obtained according to recognized standards such as ISO 1524, ASTM D1210, and GB/T 1724, and provides a systematic framework for evaluating, validating, and reporting these results. By understanding the reading criteria, precision limits, and common sources of error, laboratories and manufacturers can make reliable pass/fail decisions and optimize their dispersion processes.

Technical Overview

Fineness of grind, also known as dispersion fineness, is a measure of the size of the largest pigment and extender particles present in a liquid coating after the dispersion stage. It is one of the most widely applied routine tests in the coatings and inks industry because it directly reflects the effectiveness of the milling and dispersion process.

The measurement is performed with a grind gauge (also called a grindometer or Hegman-type gauge), which consists of a hardened steel block containing one or two channels. The channel depth decreases uniformly from a defined maximum at one end to zero at the other end. A small amount of the thoroughly mixed sample is placed in the deep end and drawn along the channel with a scraper blade. As the film thickness decreases along the channel, particles that are larger than the local channel depth protrude through the surface and become visible as a speckled or streaked pattern. The gauge depth at the characteristic reading point is reported as the fineness of grind value.

Results may be expressed in micrometers (µm), in mils, or in Hegman units (H). Approximate equivalences on the Hegman scale are listed below:

  • 4 H = 50 µm (2.0 mil)
  • 5 H = 38 µm (1.5 mil)
  • 6 H = 25 µm (1.0 mil)
  • 7 H = 13 µm (0.5 mil)
  • 8 H = 0 µm (complete dispersion below the readable range)

A finer grind value generally correlates with higher gloss, better color development, improved transparency, smoother film appearance, and fewer problems with seeding and filtration. However, the test indicates only the size of the largest detected particles, not the full particle size distribution, and this limitation must be considered when evaluating results.

Testing Samples

Solvent-Borne Coatings

Alkyd primers, industrial enamels, automotive coatings, wood finishes, and marine coatings are routinely tested. Because solvent-borne samples can skin or dry rapidly, the reading must be taken within a few seconds after the drawdown to avoid false patterns caused by solvent evaporation.

Waterborne Coatings

Architectural emulsion paints, waterborne industrial coatings, and latex-based dispersions can be tested directly. Gentle stirring is required to homogenize the sample, but excessive agitation introduces air bubbles that can be mistaken for oversized particles during evaluation.

Printing Inks and Pigment Concentrates

Offset, gravure, and flexographic inks, as well as pigment dispersions and mill bases, are commonly evaluated because these products demand very fine grind values, typically in the range of 5 to 20 µm.

Sample Conditioning and Preparation

Before testing, samples should be conditioned to the standard laboratory temperature of 23 ± 2 °C in accordance with the conditioning requirements referenced by the applicable test standard. The sample must be homogeneous; it should be stirred gently to redisperse any settled material without entraining air. Contaminated, skinned, or partially dried samples must be excluded, as they will produce invalid results.

Testing Items

The fineness of grind determination and its subsequent evaluation typically cover the following items:

  • The fineness of grind value, expressed in micrometers, mils, or Hegman units, determined at the specified reading point on the gauge channel.
  • The presence and location of oversized particles, agglomerates, gels, seeds, or foreign contamination appearing as streaks or isolated specks along the channel.
  • An assessment of dispersion quality by comparing the measured value against the product specification or the dispersion endpoint defined for the milling process.
  • Verification of repeatability by performing multiple drawdowns and confirming that the individual readings agree within an acceptable tolerance.
  • Documentation of test conditions, including the gauge range used, the applied standard, and the test temperature.

Testing Methods

Applicable Standards

  • ISO 1524 (Paints, varnishes and printing inks — Determination of fineness of grind): the international reference method, specifying gauge geometry, procedure, and reading criteria.
  • ASTM D1210 (Standard Test Method for Fineness of Dispersion of Pigment-Vehicle Systems by Hegman-Type Gauge): the North American method, reporting results in Hegman units, mils, and micrometers.
  • GB/T 1724 (Determination of fineness of grind of coatings) and GB/T 6753.1 (Grind fineness determination for paints, varnishes and printing inks): the Chinese national standards, with GB/T 6753.1 aligned with ISO 1524.

Apparatus and Gauge Selection

Grind gauges are available with maximum channel depths of typically 25, 50, or 100 µm, and with either single or dual channels. The gauge range should be selected so that the expected reading falls within a usable portion of the scale; measuring a very fine sample on a 100 µm gauge, or a coarse sample on a 25 µm gauge, reduces resolution and leads to poor evaluation quality. The gauge surface and scraper edge must be free from scratches, nicks, and corrosion, and gauge calibration should be verified periodically by accredited third-party laboratories or by certified dimensional verification.

Test Procedure

  • Clean the gauge channel and scraper with a suitable solvent and dry them thoroughly.
  • Place a representative, homogeneous sample at the deep end of the channel, slightly overfilling it.
  • Hold the scraper blade with both hands, perpendicular to the gauge surface, and draw it along the channel with a smooth, continuous stroke taking approximately two to three seconds.
  • Immediately view the wet film at a shallow angle (about 20 to 30 degrees) under oblique, glare-free lighting.
  • Identify the reading point and record the value within a few seconds, before solvent evaporation alters the surface pattern.
  • Clean the gauge and repeat the determination with a fresh portion of sample, typically for a total of at least three valid drawdowns.

Reading Criteria

Correct evaluation of the surface pattern is the most skill-dependent part of the method. Two characteristic regions are observed along the channel: a zone near the deep end where the surface appears completely smooth, and a zone where particles protrude and create a speckled or streaked appearance. The reported fineness of grind value is the gauge depth at which particles appear in a dense, clearly recognizable pattern across the width of the channel, as defined by the specific standard applied. Isolated random specks beyond this point, caused by dust or contamination, are not counted. A continuous line or deep streak running along the channel usually indicates a large agglomerate, gel particle, or a scratch in the gauge, and it should be investigated rather than simply recorded.

Evaluation of Test Results

Reporting Requirements

The test report should state the fineness of grind value rounded to the nearest gauge scale division, the units used, the specific test standard followed, the range of the gauge used, the number of determinations, and the laboratory temperature. Values should never be interpolated beyond the physical resolution of the gauge scale, and single isolated readings should not be reported without supporting replicate determinations.

Repeatability and Precision Assessment

Replicate readings obtained by the same operator on the same sample should normally agree within the smallest scale interval of the gauge. If the spread among readings exceeds this tolerance, the determination must be repeated with a fresh, freshly stirred sample, and the gauge and scraper condition should be checked. For interlaboratory comparison, differences due to operator interpretation, gauge condition, and timing of the reading are expected, so precision limits published in the applicable standard should be consulted when judging whether two results are statistically consistent.

Acceptance Criteria

Acceptance is assessed by comparing the evaluated result with the product or process specification. Typical guidance values are shown below, noting that actual limits are always defined by the product technical data sheet:

  • Primers and undercoats: commonly 40 to 60 µm maximum.
  • General industrial and architectural topcoats: commonly 20 to 35 µm maximum.
  • High-gloss and premium finishes, including automotive topcoats: commonly 10 to 20 µm maximum.
  • Printing inks and pigment concentrates: commonly 5 to 15 µm maximum.

When a result falls close to the specification limit, the decision should account for measurement uncertainty and the precision of the method; a repeat determination is recommended before rejecting or releasing the batch.

Sources of Error and Corrective Actions

  • Delayed reading on solvent-borne samples: solvent loss creates a false coarse pattern; always read within a few seconds of the drawdown.
  • Air bubbles or foam in the sample: bubbles imitate particles; degas the sample or stir more gently.
  • Tilted scraper or excessive pressure: an angled blade produces a non-uniform film and biased readings; keep the blade perpendicular and apply even pressure.
  • Scratched or worn gauge: scratches along the channel produce false streaks; inspect regularly and replace or recalibrate the gauge.
  • Incorrect gauge range: low resolution leads to rounded, uninformative results; select the gauge to suit the expected fineness.
  • Poor sample homogeneity or settled pigment: inadequate mixing gives unrepresentative results; condition and stir the sample consistently.
  • Temperature deviation: viscosity and wetting behavior change with temperature; test at 23 ± 2 °C.

Applications

Evaluation of fineness of grind results supports a wide range of technical and commercial activities:

  • In-process dispersion control, providing a rapid endpoint criterion for bead mills, sand mills, triple-roll mills, and high-speed dispersers.
  • Batch quality control and release testing of finished paints, varnishes, and inks against product specifications.
  • Incoming inspection of purchased pigment dispersions, colorants, and coating intermediates.
  • Research and formulation development, comparing the dispersing efficiency of different resins, dispersants, and milling conditions.
  • Troubleshooting production and application problems such as low gloss, seediness, poor color strength, sieve blockage, and surface defects in applied films.
  • Equipment capability studies and process validation in accredited third-party laboratories and internal quality departments.

FAQ

Does a finer fineness of grind value always indicate better paint quality?

Not necessarily. A finer value confirms that large particles are absent, which is essential for gloss, transparency, and smooth film formation. However, excessive milling increases cost and energy consumption, and poorly stabilized dispersions can reflocculate during storage. Fineness should be evaluated together with storage stability, gloss, and color development results.

Can fineness of grind replace full particle size analysis?

No. The grind gauge only detects the largest particles protruding through the film surface and provides a single endpoint value. It does not describe the full particle size distribution. For detailed distribution data, complementary instrumental methods are required.

Why do different laboratories sometimes report different values for the same sample?

Differences typically arise from operator interpretation of the reading point, gauge range selection, gauge and scraper condition, sample preparation, and the time delay before reading. Following a single defined standard, using calibrated gauges, and training operators on identical reading criteria minimizes interlaboratory variation.

How should borderline results near the specification limit be handled?

Borderline results should be repeated with fresh sample portions, ideally by a second operator. If the confirmed result remains at or just above the limit, the batch should be assessed using the precision limits of the method and the risk policy of the manufacturer, which may permit release, rework, or re-milling.

How is the accuracy of a grind gauge maintained?

The gauge should be cleaned immediately after each use, stored protected from corrosion and mechanical damage, and inspected regularly for scratches and edge wear. Periodic dimensional verification of channel depth by accredited third-party laboratories or certified measuring equipment ensures long-term result validity.

Why Choose ZKGX?

  • State-of-the-art analytical equipment
  • Highly qualified scientific team
  • Fast turnaround time
  • Competitive pricing