The Hardgrove Grindability Index (HGI) is the internationally recognized parameter that quantifies how easily coal can be pulverized, directly affecting pulverizer capacity, milling energy consumption, and combustion performance in power plants and steelworks. This article provides a complete technical guide to coal grindability index determination, covering the governing standards (ISO 5074, ASTM D409/D409M, GB/T 2565), sample preparation, apparatus calibration, test procedures, calculation, precision limits, and practical applications. It is intended for coal producers, traders, utility engineers, and quality-control professionals who require reliable and comparable HGI data.
Technical Overview
Grindability is one of the most practically important physical properties of coal, because nearly all modern thermal power stations and many metallurgical processes require coal to be pulverized to a fine particle size before combustion or injection. The Hardgrove Grindability Index (HGI) is the internationally accepted measure of the relative ease with which coal can be ground: a high HGI indicates soft, easily pulverized coal, while a low HGI indicates hard coal that demands more milling energy and reduces mill throughput.
HGI determination is an empirical, strictly standardized laboratory procedure. A prepared 50 g test portion of sized coal (0.60 mm to 1.18 mm) is ground in a calibrated Hardgrove mill under a fixed normal load for exactly 60 revolutions. The mass of ground product passing a 75 µm (200 mesh) sieve is weighed and converted into an index value using a calibration curve established with certified reference coals of known HGI. The principal standards are ISO 5074, ASTM D409/D409M, and GB/T 2565, which together ensure that results produced in different accredited third-party laboratories are technically comparable.
- Property measured: relative grindability (pulverizability) of coal on an air-dried basis
- Result expressed as: dimensionless HGI value, typically between 30 and 110
- Governing standards: ISO 5074, ASTM D409/D409M, GB/T 2565
- Primary users: power generators, steel producers, coal traders, pulverizer manufacturers, and coal quality laboratories
Because HGI correlates directly with pulverizer output, mill power draw, and achievable product fineness, it is a mandatory specification parameter in most international coal supply contracts and a key input to boiler and mill design.
Testing Samples
Bituminous Coal and Anthracite (Hard Coal)
Hard coals are the primary scope of the ISO and ASTM Hardgrove methods. Bituminous coals typically yield HGI values between 40 and 100, while anthracites are generally harder, with values commonly in the 35 to 60 range. Run-of-mine coal, washed products, and trade cargoes can all be tested provided the sample is representative and correctly prepared.
Sub-bituminous Coal and Lignite
Lower-rank coals may also be tested, but results must be interpreted with caution. These coals contain high inherent moisture, which can behave plastically during grinding, and the empirical calibration of the Hardgrove machine is strictly validated only for hard coal. Moisture conditioning and careful air drying are essential, and the reported HGI should always be accompanied by the moisture state of the sample.
Coal Blends and Other Carbonaceous Materials
Blends, washed middlings, and certain carbonaceous solid fuels (for example petroleum coke or char, where the client and laboratory agree on method applicability) can be measured directly. Note that the HGI of a blend is not a simple weighted average of its components and should be determined experimentally on the blended material.
Minimum Sample Requirements
A laboratory sample of approximately 1 to 2 kg of coal crushed to a nominal top size of a few millimeters is normally sufficient. After air drying, gentle stage crushing, and sieving, at least 200 g of the 0.60–1.18 mm fraction should be available to permit duplicate determinations and, if necessary, repeat preparation. Samples must be protected from contamination, over-crushing, and moisture change between sampling and testing.
Testing Items
The core deliverable of the test is the Hardgrove Grindability Index itself; supporting determinations are frequently performed to support interpretation and reporting.
- Hardgrove Grindability Index (HGI), reported to the nearest whole number on the air-dried basis
- Air-dried moisture content of the test sample, required for traceability and interpretation
- Optional proximate analysis (ash, volatile matter, fixed carbon) to contextualize the HGI against coal rank and mineral matter content
- Optional duplicate or check determinations to demonstrate repeatability compliance
Typical commercial HGI bands are approximately as follows: very hard coals below 40, moderately hard coals 40 to 55, average coals 55 to 70, soft coals 70 to 90, and exceptionally soft coals above 90.
Testing Methods
Sample Preparation
The laboratory sample is air dried to equilibrium and then crushed gently, using a jaw crusher or roll mill set to minimize the generation of fines. The crushed material is sieved, and the 0.60 mm to 1.18 mm (30 × 16 mesh) fraction is retained as the test sample; material finer than 0.60 mm is discarded. The sized fraction is thoroughly mixed, and a test portion of 50 g ± 0.01 g is weighed out for each determination.
Apparatus and Calibration
The Hardgrove grindability machine consists of a stationary lower grinding ring carrying eight hardened steel balls of 25.4 mm (1 inch) diameter, and a driven upper grinding ring to which a normal load of 284 N ± 2 N is applied. The machine rotates at 20 r/min ± 1 r/min. Supporting equipment includes calibrated 1.18 mm, 0.60 mm, and 75 µm test sieves, a mechanical sieve shaker, and a balance readable to 0.01 g. Each instrument must be calibrated with a minimum of four certified reference coals spanning the HGI range of approximately 40 to 110, traceable to recognized standards bodies, and the calibration must be verified periodically and after any maintenance.
Determination Procedure
The 50 g test portion is distributed evenly over the grinding balls, the machine is assembled with the specified load, and grinding proceeds for exactly 60 revolutions ± 0.25 (approximately three minutes). The entire ground product is then transferred to the 75 µm sieve and sieved mechanically, typically for about 10 minutes or until continued sieving produces no further significant mass change. The mass of material passing the 75 µm sieve is weighed to the nearest 0.01 g.
Calculation and Expression of Results
The baseline relationship defined by the standards is HGI = 13 + 6.93 × m, where m is the mass in grams of product passing the 75 µm sieve. In practice, the measured passing mass is converted through the machine-specific calibration regression established with the reference coals. The final result is rounded to the nearest whole number. Duplicate determinations are normally performed, and the mean is reported if the difference between duplicates does not exceed the repeatability limit; otherwise the determination is repeated.
Precision and Quality Control
Under ISO 5074, results within the same laboratory should agree within approximately 2 HGI units (repeatability), and results between different competent laboratories within approximately 3 HGI units (reproducibility); ASTM D409/D409M defines comparable limits that vary slightly with the HGI level. Because the method is empirical, results are only valid on the calibrated instrument, and regular verification with reference coals, participation in interlaboratory proficiency programs, and documentation of machine wear are essential elements of quality control in accredited third-party laboratories.
Applications
HGI data are used throughout the coal value chain, from mine planning and coal preparation to trade settlement and plant operations.
- Pulverizer selection and sizing: HGI is a primary input for specifying bowl mills, ball mills, and beater-wheel mills in new power station and boiler projects
- Mill capacity and energy assessment: as a first engineering approximation, mill output is scaled in proportion to the ratio of actual to design HGI, with lower HGI causing measurable derating and higher specific power consumption
- Combustion optimization: grindability determines whether the required fineness (commonly 65 to 80 percent passing 75 µm, depending on rank) can be achieved economically, affecting ignition stability, unburned carbon in ash, and emissions
- Coal trade and contracts: HGI is a standard specification parameter, frequently linked to price adjustments or rejection clauses in international supply agreements
- Steelmaking: pulverized coal injection (PCI) systems in blast furnaces depend on HGI to achieve injection fineness at acceptable grinding costs
- Cement and industrial boilers: kiln and boiler operators use HGI to evaluate fuel suitability and blending strategies
- Coal blending and research: HGI trends with rank, maceral composition, and mineral matter support blend design and coal characterization studies
For plant operators, the practical consequence is direct: a coal delivered 10 HGI points below the design value can significantly reduce pulverizer throughput, force mill shutdowns for maintenance, and increase auxiliary power consumption, which is why buyers and engineers treat certified HGI results as commercially critical data.
FAQ
What does a high HGI value mean?
A high HGI (for example, above 70) means the coal is soft and easy to pulverize: the mill achieves its target fineness at higher throughput and lower specific energy consumption. A low HGI (below about 50) indicates hard coal that reduces mill capacity and increases grinding power demand.
How much sample is required for HGI testing?
A laboratory sample of roughly 1 to 2 kg of crushed coal is sufficient. After preparation, duplicate 50 g test portions of the 0.60–1.18 mm fraction are used for the determinations.
Which standards govern the determination?
The principal methods are ISO 5074 (Hard coal — Determination of Hardgrove grindability index), ASTM D409/D409M (Grindability of coal by the Hardgrove-machine method), and GB/T 2565, the Chinese national standard technically aligned with the ISO approach.
How is the HGI actually calculated?
The mass of ground product passing a 75 µm sieve is inserted into the instrument calibration curve. The reference formula is HGI = 13 + 6.93 × m, where m is the passing mass in grams, but each machine must use its own regression established with certified reference coals.
How reproducible is the test?
When performed on a calibrated instrument in a competent laboratory, duplicate results should agree within about 2 HGI units, and results between different laboratories within about 3 units. Poor sample preparation, worn grinding elements, or inadequate calibration are the usual causes of excessive scatter.
Does moisture affect the result?
Yes. HGI is determined on an air-dried basis, and the moisture condition of the test portion influences grinding behavior, particularly for high-moisture sub-bituminous coals and lignites. The moisture state should always be reported alongside the index.
Is HGI the same as the Bond Work Index?
No. HGI is an empirical, dimensionless index derived from a fixed standardized grinding procedure, whereas the Bond Work Index expresses grinding energy in kilowatt-hours per tonne. The two are correlated for many materials, but they are distinct parameters obtained by different test methods.
How long does HGI testing take?
In accredited third-party laboratories, routine HGI determination, including sample preparation, calibration verification, and duplicate measurement, is typically completed within one to three working days of sample receipt.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing